About This Item

Share This Item

The AAPG/Datapages Combined Publications Database

Houston Geological Society Bulletin

Abstract


Houston Geological Society Bulletin, Volume 45, No. 4, December 2002. Pages 13, 15, and 17.

Abstract: Grayson Field, Jurassic Smackover Reservoir, Columbia County, AR: A Case Study Using Leading Edge Reservoir Characterization Seismic Processing of 3D Seismic Data

By

Kevin B. Hill1 and William R. Meaney2
1 Hill Geophysical Consulting, Shreveport, LA
2 Anderson Oil and Gas, Shreveport, LA

The discovery well at Grayson Field, Columbia County, Arkansas, was drilled on a four-way dip closure defined by three 2D seismic lines. Investors were hoping to find a maximum of 100 feet of pay. After the discovery of 158 feet of pay at 8000 feet (measured depth) in the Jurassic Smackover limestone in January 1993, the participants decided that a 3D seismic program was needed. The objective of the 3D seismic program was to define the structural and stratigraphic limits of the new field.

Specific processing and interpretive tools will be illustrated with many different seismic displays. Evidence will be presented that 1) relative amplitude of the Smackover reflector does not define the reservoir's stratigraphic parameters, 2) attributes of the acoustic impedance data (inversion) show good statistical correlation to key reservoir parameters, 3) Previous HitAVONext Hit shows a hydrocarbon indicator over the reservoir, and 4) reservoir characterization data (petrophysical volumes generated with Hampson-Russell Emerge software) generated with the 3D seismic data delineates the production.

The Grayson field Smackover reservoir was originally divided into two zones. The upper 35 feet of the reservoir is dolomitic lime with high porosity (20-25%) and moderate to low spotty permeability of 10-100 md. The main pay zone is approximately 40 feet below the top of the Smackover. It has primary oolitic porosity of 17-20% with permeabilities into the darcies. The separation between the pay zones ranges from 1 to 10 feet. Through the use of this fully integrated sub-surface well information and a 3D seismic data set, the thinner upper pay interval can be discerned from the thicker main pay. Horizontal well programs have been designed using the 3D seismic data to exploit the best porosity and permeability in the upper pay interval. Vertical wells adequately drain the main, lower pay interval.

In July 1995, gas injection was begun in the field. In February 1998, a water flood program replaced the gas injection. In-fill drilling was needed to optimize the production. 3D seismic data was needed for this work, but the resolution of the reservoir was not really clear enough on the original processing. Reprocessing of the data set with "state-of-the-art" parameters such as detailed editing of each shot record, pre-stack time migration~ and post-stack inversion (acoustic impedance), Previous HitAVONext Hit, and petrophysical cubes was needed. The full integration of the entire suite of logs from every well in the area into the poststack processing of the 3D data yielded multiple data volumes. The bandwidth of the reprocessed data is 15--90 hertz, with a dominant frequency of 43 hertz. With the broad

Unnumbered Figure. Smackover structure map with location of Smackover fields in Columbia County, Arkansas. Map courtesy of Geological Consulting Services. @GCS 2002.

End_Page 13---------------

bandwidth and integration of the well log information, the new data volumes show the stratigraphic components of the reservoir very clearly.

The Previous HittuningNext Hit thickness of the wavelet at the Smackover level is 9 milliseconds (approximately 54 feet). Identification bf the upper and lower pay intervals is very difficult because the upper zone is thinner than the Previous HittuningNext Hit. The two pay zones appear to merge into one thick, high-amplitude seismic event. The sonic and density logs from the wells were used to calibrate and generate an acoustic impedance data volume. This multi-linear regression technique yields a data volume that better defines the two layers within the reservoir. The acoustic impedance (velocity) of the upper 100 feet of the Smackover was evaluated with different attributes to see if there was a correlation to the overall reservoir. Cross-plots of certain seismic attributes exhibit a good statistical fit with the reservoir's porosity and pore-volume maps generated from well information. The Grayson field Smackover reservoir is a low-velocity zone encased within high-velocity rocks. This is a classic Type III Previous HitAVONext Hit case.

Unnumbered Figure. North-south dip line from 3D seismic data showing water saturation data volume calculated with Archie's equation.

Unnumbered Figure. The average of the top 100 ft. of the Smackover indicates that there may be some low velocity areas on the west end of the structure. However, low velocity was only indicative of porosity and the permeability was virtually absent on the western end. Only Grayson field is seen on this map. The oil wells in the upper right corner are Barlow Branch field.

Unnumbered Figure. Comparison of "porosity" 3D seismic data volume (top) and "water saturation" 3D seismic data volume (bottom). The "water saturation" volume properly defines the stratigraphic limits of the reservoir.

End_Page 15---------------

A positive Previous HitAVONext Hit P*G (primary times gradient) response is seen at the producing wells, whereas no Previous HitAVONext Hit P*G response is observed in the non-producing areas.

The difficulty of identifying the Previous HitthinNext Hit upper pay interval was overcome by making deep induction and gas effect "seismic" volumes that could be used in conjunction with the relative amplitude, Previous HitAVONext Hit, and acoustic impedance volumes. The seismic data quality was very good and a sufficient population of well bores, with the target attributes, was available. Hampson-Russell Emerge software was used for the reservoir characterization data generation. This is an artificial neural network algorithm that successfully computed the deep induction, density porosity, and neutron porosity volumes.

Cross-plotting the density porosity and neutron porosity data volumes generated a gas effect "seismic" volume. The results of this data volume were outstanding. The thick pay interval at Grayson field as well as a Previous HitthinNext Hit stratigraphic pay at Barlow Branch field stood out extremely well.

The hydrocarbon saturation and water saturation can be calculated using Archie's equation with the "seismic" deep induction and density volumes. The data show the upper and main pay intervals as well as a possible separate deeper zone. The deeper zone has produced in two wells, and it was originally thought to be connected to the main pay zone. However, the new processing shows this zone to be separated from the main pay zone by at least 15 feet throughout the field. Further evaluation of this interval is ongoing.

The acoustic impedance data show low velocity (porosity) extending outside of the known producing limits of the field whereas the oil and water saturation volumes show the definitive limits of the pay interval. The oil and water saturation volumes also more dearly define the separation of the three different pay zones within the reservoir.

Conclusion

3D seismic data played a significant role in the development of Grayson field. The 3D seismic data allowed Petro-Chem Operating Company to drill the best structural locations within the field. Reprocessing the 3D seismic data brought out the stratigraphic nuances of the field. The relative amplitude strength of the top Smackover reflector does not define any reservoir parameters. The acoustic impedance data volume shows a good statistical correlation to the gross reservoir parameters of the upper 100 feet of the Smackover. Multi-attribute inversion using an artificial neural network algorithm (Emerge) successfully computed the deep induction, density porosity, and neutron porosity volumes. "Seismic" volumes of gas effect, water saturation, and hydrocarbon saturation dearly delineate the reservoir. New wells drilled using these 3D seismic volumes greatly increased the production rate and ultimate recoverable reserves in the field. Recent drilling proves that the 3D seismic effort and expense were well worth the money.

Unnumbered Figure. Relative amplitude of the top Smackover reflector with subsurface and seismic depth contour overlay. Arb line represents the seismic line seen on page 15.

Unnumbered Figure. "Gas effect" calculated by taking the density porosity 3D seismic volume minus the neutron porosity 3D seismic volume.

End_of_Record - Last_Page 17---------------

 

Copyright © 2005 by Houston Geological Society. All rights reserved.