About This Item
- Full text of this item is not available.
- Abstract PDFAbstract PDF(no subscription required)
Share This Item
The AAPG/Datapages Combined Publications Database
Houston Geological Society Bulletin
Abstract
Abstract: Rigorous Computer Processing of
Multiple Non-Vertical Intersecting
Faults among Multiple Surfaces
By
pMaping-Contouring System (MCS) treats faulted systems as what they are: Sets of three-dimensional blocks containing geological markers (formation tops) which once were continuous surfaces. The boundaries of these fault blocks are contourable surfaces and are the fault surfaces.
MCS processes faulted systems in three steps designed to honor continuity of shape across faults.
- MCS first moves the fault blocks to their pre-faulted positions together with the contained formation tops.
- Then, having restored the "Continuous surface"
attribute to the geologic markers, MCS performs all
the "Stacking" (discussed later) and interpolations
needed to obtain a smooth map or
cross
-
section
.
- The third step is to rebreak, i.e. reverse the first step
and return the fault blocks and their contents to
their faulted positions, and to display as contour
maps or
cross
-sections.
To accomplish these steps MCS needs certain data and a set of instructions:
To MCS, fault vertical displacement or vertical separation is just another mathematical surface which can vary over the mapped area and can be contoured. When displacements are positive throughout, MCS automatically processes a normal fault. When displacements are negative, MCS processes a reverse fault. Scissors faults result from displacements which change signs within the mapped area. Areas with zero displacement show where a fault ceased to exist. Some growth faults can be modeled with displacements which show great variation across the mapped area.
The user of MCS should (usually) first analyze the fault
system by making contour maps or cross
-sections of all the
faults in order to:
- Test the faults for reasonableness, e.g., do observed fault cuts that have been assigned to the same fault result in a picture that makes sense?
- Infer and/or ascertain the hierarchy of the faults, i.e., when two faults meet in space, which one survives? Which one is, therefore, older?
- Infer and/or ascertain which faults form boundaries of a fault block.
The analysis easily lends itself to "what if' games, i.e., the testing of various hypotheses.
The instructions MCS needs to perform its task are a set of RESTORE commands, each of which describes a fault block and instructs MCS to move it to its pre-faulted position. The RESTORE commands takes us "back in time," i.e. the first RESTORE reverses the most recent faulting event, the last RESTORE reverses the oldest event.
The sequence and makeup of the RESTORE instructions is derived from an analysis of the fault and any a priori knowledge of the area.
Consider a system with two antithetic faults, Fault 'A' and Fault 'B', both of which are shown in Figure 1. Since Fault 'B' dies against Fault 'A', Fault 'B' is presumed to be younger. Fault 'A' is presumed to be the older fault, and the system can be divided into three blocks: 1) Above 'B' and above 'A', 2) Below 'B' and above 'A', and 3) Below 'A'.
In keeping with the principle that RESTORE commands are taking us "back in time,'' we must restore first the block which was displaced during fault event 'B', i.e., the block which lies above 'B' and above 'A', hence:
RESTORE (Above) 'B' Above 'A'
Next we must restore the block moved during fault event 'A' which is the block above Fault 'A' and which, incidentally, contains Fault 'B':
RESTORE (Above) 'A'
When MCS has finished complying with these commands it would have, in effect, accomplished a vertical, sequential, three-dimensional palinspastic reconstruction of the fault system. Now that the faulted system has been restored to its pre-faulting configuration, the structural surfaces are continuous and can be stacked.
Multi-Surface Stacking:
In areas of conformable geology, adjacent formations resemble each other. MCS uses the principle of conformable geology in its multi-surface stacking process. MCS
End_Page 12---------------
first calculates isopachs (differences in value between adjacent surfaces) wherever possible. These isopachs are interpolated or extrapolated over the entire map area for all isopach intervals. Calculated isopach values are added or subtracted from known datums in order to reconstruct a complete set of Z values at all data points. This "stacking" proceeds downward first and upward second.
As a result of fault restoration and multi-surface stacking there is a continuity of shapes (geologic features) across faults, and MCS does reasonable contouring in fault blocks which have no well or seismic control.
Final Step in Fault Processing
The final step in MCS fault processing is to re-break and move geologic surfaces to their true (post-faulted) positions. This step is the mathematical inverse of restoration. MCS generates fault traces as the intersection between structural surfaces and faults. Rigorous displacement or separation balance is achieved at all fault intersections. Figures 2 and 3 show contour maps for the 8500- Ft. and 9200-Ft. sands.
Figure 1.
Cross
section
showing the time-sequence of two antithetic faults.
Figure 2. Contour map for the 8500 Ft. sands.
Figure 3. Contour map for the 9200 Ft. sands.
End_of_Record - Last_Page 13---------------