About This Item
- Full text of this item is not available.
- Abstract PDFAbstract PDF(no subscription required)
Share This Item
The AAPG/Datapages Combined Publications Database
Houston Geological Society Bulletin
Abstract
Abstract: Pressure Trends in Lower Viosca Knoll and Mississippi Canyon, Gulf of Mexico
Deep Water: Implications for Seals, Column Heights and Hydrocarbon Migration
By
Amoco Production Company
Analysis of pressure data from forty-one deepwater wells in the northern Gulf of Mexico has revealed consistent patterns in the rates of increase of both pore pressure and fracture gradient with increasing depth. Several conclusions may be drawn from these patterns, including:
Pore pressure (PP) and fracture pressure (FP) trends are not parallel with increasing depth. PP and FP converge at the mudline. The small differences between pore pressure and fracture pressure in the shallow section of a well directly influence the openhole drilling distance allowable between casing sets. In addition, these close tolerances can exacerbate problems in controlling shallow water or gas flows that may be encountered.
Pore pressure is elevated above a "normal" hydrostatic trend at shallow sediment burial depths. Indications are that top seals form with as little as 1500' -2000' of sediment burial. Such early seal
formation is favorable to the formation of stratigraphic traps. It also sets a maximum depth for conventional riserless drilling.
Pore pressure and fracture pressure trends diverge with increasing depth in sedimentary sections with high sedimentation rates. This divergence, DPP < DFP, directly limits the column height. As the difference increases, the maximum column height possible also increases.
Conversely, pore pressure and fracture pressure converge, DPP > DFP, in deeper sections associated with lower sedimentation rates and unconformities. As a result, maximum possible column heights decrease in these intervals and may actually preclude sealing any significant volumes of hydrocarbons.
These trends of increasing/decreasing sealing capacity have application to models of generation, expulsion, primary and secondary migration and accumulation of hydrocarbons in this area. Areas of reduced sealing capacity in the deeper sedimentary section will "frac," allowing vertical migration of fluids to zones with higher sealing capacities.
Introduction
Pore pressure trends were analyzed in forty-one wells to support deepwater drilling activity, particularly in the Viosca Knoll and Mississippi Canyon protraction areas (Figure 1). The goal was to predict pressure cells as an aid to well design, prior to drilling, because of the high costs of deepwater operations. Pressure trends were analyzed to define regional patterns of pressure increase with depth. As this effort continues, a number of characteristic patterns in the relative rates of increases of pore pressure and fracture pressure were observed in all the wells analyzed. Implications drawn from these patterns extend beyond the original drilling-related focus of the project to include influence on column heights, sealing capacity and hydrocarbon migration issues.
Methods
Pressure data were compiled for the existing wells in the area prior to Amoco initiating its drilling program in 1992. As additional wells were drilled they were included in the database. The data collected included direct pressure measurements from drill stem test (DST) and repeat-formation (RFT) or modular-dynamic (MDT) testing tools with pressure equivalents from drilling mud weights and associated leak off tests (LOT). In addition, pressure estimates from empirical relations of travel time and resistivity were applied to acoustic and resistivity logs. The acoustic algorithm was also applied to seismically derived velocity profiles from migration before stack (MBS) data for pre-drill pressure prediction.
All the data were analyzed using PRESGRAF, a proprietary PC-based program that allows analysis and presentation of pressure data of various types and from multiple wells (Traugott, 1997). The methodology employed was first to create a calibrated pressure profile for known wells and then to extrapolate the profile to new drilling locations, usually using MBS seismic data. A plot from a typical well is presented in pressure (psi) vs. depth (Figure 2) and mud-weight vs. depth (Figure 3).
First an overburden trend (pressure vs. depth) was created for an existing well. There are two components to overburden in deepwater. First, the water column
Figure 1. Index map of study area.
End_Page 8---------------
pressure (water depth x 0.455 psi/ft). The average lithostatic pressure component was established using the density log from the well. Total overburden at any depth below mudline is the sum of the water column and lithostatic overburden components. Estimates of the overburden trend can be compared to measured LOT data which imposes a boundary condition on the estimate. Second, after establishing an overburden trend, measured pore pressure data from DST or the RFT/MDT log was input. Mud-weight and LOT data was also input at this time. These measured values set boundary conditions on subsequent estimates of pore pressure created from wireline log data. Sonic log data were incorporated next and was processed iteratively with a pressure estimating algorithm within PRESGRAF. The general relation of the algorithm is: pore pressure (PP) is proportional to travel time (DT), porosity at the surface1 mudline (Po), volume clay (Vcl) and a compaction constant (C).
PPµ DT x Po x Vcl x C
Some of these values may be estimated from log or geotechnical core data (Vcl, Po). The others are varied iteratively to produce a result that conforms to the preexisting boundary conditions imposed by mud-weight and measured pressure data.
Finally, an independent estimate is made using the resistivity data. Though it uses a different algorithm than the sonic estimate, a number of variables are common to both; Po, Vcl and C. The new variables in the resistivity estimate are resistivity (RT) and the cation-exchange-capacity (CEC). A temperature profile for the well is also necessary due to the variations in RT with temperature. The resistivity estimate is computed and compared to the sonic value. The two algorithms are solved iteratively until a close match is achieved using common values for Po, Vcl and C.
Once a calibrated model was created for a known well, that model (with adjustments for variations in water depth) was used for pre-drill estimates of pressure for new drilling locations. The sonic algorithm was especially useful for pre-well locations that had MBS seismic. A velocity profile extracted from the MBS velocity volume can be processed in a similar manner to the sonic log. This gives a direct pre-drill estimate of pressure at the well location. Seismic velocity uncertainty will propagate through the model as a resultant uncertainty in the absolute estimated pressure, however the rates of change in estimated pressure and any associated inflection points in the pressure profile, have significance in establishing depths to major pressure cell boundaries.
During drilling operations, the calibrated resistivity model values may be applied to measured-while-drilling (MWD) resistivities to evaluate pressure trends in the well in real time.
Conclusions
Several general conclusions can be drawn from the data. Most are easily extrapolated to other areas in the Gulf of Mexico offshore and to other clastic, passive margin basins. Others are currently specific to the geology of the local area, and cannot yet be extrapolated to other areas.
Fracture pressure and pore pressure trends converge near the mudline (point "A" in Figures 2 and 3). This convergence sets a physical limit on the amount of open-hole that can be maintained before setting additional casing strings becomes necessary. In this shallow section below the mudline, more time and expense are expended setting and cementing casing than in drilling.
These narrow tolerances, typically a few tenths of a pound-per-gallon (PPG) equivalent, between PP and FP can make control of shallow pressure flows difficult. While increasing mud weight to control flows a slight overbalance can break down formation causing loss of drilling fluid. After this loss, the flowing formation comes back into the well. This cycle of flow/kill/breakdown/ flow can result in substantial well cost overruns.
Seals form earlier and at shallower depths
below mudline in the deep water environment
compared to shelf sediments (point
"B" in Figures 2 and 3). Water column is
a contributing factor, with the water
column providing an overburden stress
approximately equivalent to a column of
rock half this thickness. The water column
effect is most noticeable in water depths
exceeding ~2000'. Pore pressures are
elevated above hydrostatic pressure with
as little as 1500'-2000' of sedimentary
overburden deposited. This early top-seal
formation sets up a favorable system to
trap early migrating hydrocarbons. The
study area has a relatively large number
of fields/discoveries with significant
stratigraphic components.
Pore pressure and fracture pressure increase at different rates with increasing burial depths. These differential rates of pressure increase result in variations of potential column heights with increasing depth. In the younger, expanded Miocene sections, characterized by high sedimentation rates, the rate of pore pressure increase is lower than the increase in fracture pressure (DPP< DFP). In the deeper, older section there are transitions into higher pressure cells where the rate of change in pore pressure is higher than the
Figure 2. Pressure (PSI) versus Depth (ft.) for a typical well, MC 84.
End_Page 9---------------
fracture trend gradient (DPP > DFP).
In the expanded Miocene section of the
study area, pore pressure increases at ~0.8 psi/ft, whereas fracture pressures increase
uniformly at ~1.0 psi/ft. (point "C' in
Figures 2 and 3). This separation results in
increased seal
potential and therefore
greater possible maximum column heights
with increasing depth. Three fields in the
area are filled to spill, having hydrocarbon
columns of 2100' (Neptune), 1900'
(Marlin) and 1400' (King). An additional
benefit, this pressure gradient differential
increases the depth interval that can be
drilled after each succeeding casing point
resulting in reduced total drilling time.
A few wells drill completely through the
expanded Miocene to the Lower Tertiary
and Upper Cretaceous sections. This older
stratigraphic section has significantly
lower rates of sedimentation, as well as
significant unconformities, and is associated
with a notable transition to higher
pressures. The pore pressure gradient
increases abruptly (1.8 psi/ft) in the transition
zone (point "D" in Figures 2 and 3).
The separation between pore pressure and
fracture trends is substantially reduced,
resulting in diminished seal
capacity and
an accompanying reduction in maximum
possible column height. An additional
drilling consideration is that the transition
may be quite abrupt with pressure
differentials of 2000-3000 psi occurring
in as little as 120' of vertical section.
In this local area the succession from
the mildly pressured Miocene reservoirs,
with high seal
capacity, to the lower
Tertiary and Cretaceous source rocks,
with significantly decreased sealing
capacity, provides a probable mechanism
for expulsion and vertical migration of
hydrocarbons. On deep high relief
structures in the deep source section,
any significant accumulation of hydrocarbons
will result in buoyancy pressures
that exceed the
fracture pressure
sealing capacity.
At that point,
hydrocarbons can
fracture the top
seal
and move
vertically along
salt/sediment interfaces
or faults that
extend up to the
Miocene. Once
above the pressure
transition, hydrocarbons
then charge
lower pressured
sands that have
higher sealing
capacity.
Figure 3. Mud weight (ppg) versus depth (ft.) for a typical well, MC 84 #1. Pressure (psi) versus depth (ft.) for a typical well, MC 84.
End_of_Record - Last_Page 11---------------