About This Item

Share This Item

The AAPG/Datapages Combined Publications Database

Fort Worth Geological Society

Abstract


Southwest Section, AAPG Annual Meeting. Onshore Applications of 3-D Previous HitSeismicNext Hit Technology, A Short Course, February 21, 1993.

 

ONSHORE APPLICATIONS OF 3-D Previous HitSEISMICNext Hit TECHNOLOGY

INTRODUCTION/OVERVIEW

Tom Davis - Colorado School of Mines
Steve Roche - Halliburton Geophysical Services, Inc.
Susie Mastoris - Landmark Graphics Corporation

A 3D reflections Previous HitseismicNext Hit survey provides information about the subsurface geology, the information available ranges from structural to stratigraphic. Structural information is generally thought of as the "geometry" of the reflecting horizons, their positions and dip relative to each other. Stratigraphic information can be thought of as relating reflection amplitude to change in lithology. An example would be a large amplitude reflection from a shale-dolomite interface where there is a large change in acoustic impedance. Structural and stratigraphic information are not two separate types of information, but represent the extremes across a range of available data.

It is important to note that reflection Previous HitseismicNext Hit data does not provide a cross-section detailing specific rock type. Previous HitSeismicNext Hit data is a measure of reflectivity, changes in acoustic impedance, measured in time. Information about the subsurface geology is inferred from the Previous HitseismicNext Hit data and geologic control, such as well logs, is required. Since Previous HitseismicNext Hit data is measured versus time, the exact depth to a reflecting horizon can only be determined if the velocity of the media is known. Velocity is the unknown variable. Many aspects of the 3D project design, acquisition and processing methods are utilized to gain a more accurate estimation of the subsurface velocity.

The acquisition and processing of Previous HitseismicNext Hit data involves many of the same technologies as the communications industry. Specifically the sampling of analogue waveforms and the digital processing of that information. The rate at which one samples the data is one of the main determining factors in the resolution capabilities. Sampling occurs in time, typical surveys are sampled at 2 millisecond, or 500 times per second. 3D Previous HitseismicNext Hit surveys are sampled in space as well, the source and receiver intervals are the digital sampling of an analogue waveform at the earth's surface. How closely sampled the Previous HitseismicNext Hit data is directly determines the size of the geologic anomaly that can be resolved. The frequency content of the data is another factor in the resolving power of the final data volume. Typically, the frequency content is determined by the type of source used to generate the sound waves and the digital processing methods used to recover those frequencies. The initial sampling of the Previous HitseismicNext Hit data, in time and space, is a limiting factor on the frequency content. Noise and the attenuation properties of the earth serve to limit the resolution of the data.

To obtain the maximum resolution from the Previous HitseismicNext Hit data volume the data must be correctly positioned in x, y and t. With knowledge of the velocity field of the subsurface the data can be regarded as being correctly positioned in x, y and z (depth). It is important to understand that the Previous HitseismicNext Hit data does not necessarily lie directly beneath the source or receiver, or even beneath the straight line traverse between them. 3D acquisition and processing techniques, specifically "3D migration", are what image the data in its correct spatial location in the subsurface.

Many errors associated with using 2D data are due to the fact that the reflections on a section need not be in the plane of the 2D traverse. The reflections presented on a 2D profile are those reflections recorded on the surface of a cylinder. For abrupt features such as pinnacle reefs, a 2D line can record the image of the reef but incorrectly portray the location as being beneath the 2D traverse. 3D Previous HitseismicNext Hit will accurately image the reef in its correct location. Extreme velocity gradients used to tie 2D data to well control can also be resolved once 3D techniques are used to correctly position the subsurface geology. The primary advantage of 3D methods over the previous Previous HitseismicNext Hit methods is twofold ...

1. The position of the reflectors (structure) is known.

2. The changes in the Previous HitseismicTop data character can be used to infer changes in lithology.

 

Copyright © 2004 by Fort Worth Geological Society. All rights reserved.

Tom Davis, Steve Roche, and Susie Mastoris

View the First Page

A text abstract of this article is not available. The first page of the PDF appears below.

You may download the first page as a PDF.

Pay-Per-View Purchase Options

The article is available through a document delivery service. Explain these Purchase Options.

Watermarked PDF Document: $14
Open PDF Document: $24