About This Item
- Full TextFull Text(subscription required)
- Pay-Per-View PurchasePay-Per-View
Purchase Options Explain
Share This Item
The AAPG/Datapages Combined Publications Database
AAPG Special Volumes
Abstract
fault
and cap rock seals
DOI:10.1306/1060764H23169
2005 by The American Association of Petroleum Geologists.
Sealing by Shale Gouge and Subsequent Seal Breach by Reactivation: A Case Study of the Zema Prospect, Otway Basin
Paul J. Lyon,1 Peter J. Boult,2 Richard R. Hillis,1 Scott D. Mildren3
1Australian School of Petroleum, University of Adelaide, Australia
2Australian School of Petroleum, University of Adelaide, Australia and also Department of Primary Industries and Resources South Australia, Adelaide, Australia
3Australian School of Petroleum, University of Adelaide, Australia; Present address: JRS Petroleum Research Pty. Ltd., Magili, Adelaida, Australia.
ACKNOWLEDGMENTS
Peter Bretan, Andrew Davids, Richard Suttill, and Paul Theologou are thanked for their constructive reviews. Origin Energy and its joint venture partners are thanked for the provision of 3-D seismic data and regional near top Pretty Hill Formation horizon. All staff and students at the Australian School of Petroleum, University of Adelaide, are thanked for advice, guidance, and sharing of technical expertise. We particularly acknowledge the key contribution made by fellow researchers in the Stress Group (Australian School of Petroleum) and the Australian Petroleum Cooperative Research Center. All staff members at Badleys Geoscience Ltd. are thanked for their excellent software support and guidance and provision of Traptester software. Jerry Meyer of JRS Petroleum Research Pty. Ltd. and Quentin Fisher of Rock Deformation Research, University of Leeds, are also thanked for their informative comments and advice. Primary Industries and Resources of South Australia Publishing Services are thanked for their assistance in the drafting of Figures 1, 2, 3 and 7.
ABSTRACT
The Zema prospect, located in the Otway Basin of South Australia, hosts an interpreted 69-m (226-ft) paleohydrocarbon column. Two faults are significant to prospect integrity. The main prospect-bounding fault
(Zema
fault
) shows a significant change in orientation along strike, with some parts of the
fault
trending northwest–southeast and other parts trending east–west, all at a consistent dip of about 70
. The
fault
shows a complex splay and associated relay zone at its western tip. An overlying
fault
shows a similar northwest–southeast trend.
Shale volume (Vshale) derived from the gamma-ray log was tied to seismic horizon data in order to model across-fault
juxtaposition and shale gouge ratio on the Zema
fault
. Shale volumes of greater than 40% correspond with paleosol shale lithotypes identified in the core that are characterized by high mercury injection capillary entry pressures of 55 MPa (8000 psi), capable of supporting gas columns far beyond the structural spillpoint of the trap. Vshale values of 20–40% correspond to silty shale lithotypes characterized by mercury capillary entry pressures equivalent to gas column heights of less than 30 m (100 ft). Sands correspond with Vshale values of less than 20%.
Juxtaposition modeling of the Pretty Hill reservoir interval that is displaced across the Zema fault
against the Laira Formation seal demonstrates the existence of both sand-on-sand juxtaposition and sand-on-silty shale juxtaposition above the paleofree-water level. Hence, juxtaposition alone cannot explain the observed paleocolumn. It is therefore likely that
fault
damage processes on the
fault
plane were responsible for holding back the original 69-m (226-ft) column. Shale gouge ratio values show a gradual decrease from 32% at the top of the
fault
trap to less than 14% at the structural spillpoint. The
fault
damage zone is likely to consist of phyllosilicate framework rock types. Because the Zema trap was not filled to structural spillpoint, it is likely that the percentage of shale gouge in the
fault
zone not only provided the original sealing mechanism but also limited the original column height. This is supported by
fault
zone capillary entry pressures calculated from shale gouge ratio values, which indicate that the
fault
zone is only capable of supporting a maximum column height of 72 m (236 ft), just 3 m (10 ft) more than the interpreted column height of 69 m (226 ft).
Geomechanical analysis shows that the northwest–southeast-trending parts of the faults are optimally orientated in the in-situ stress field for reactivation. A spontaneous potential (SP) anomaly in the Zema-1 well, which was recorded in a northwest–southeast-striking fault
damage zone through the seal, confirms the existence of open, permeable fracture networks. These are likely to have been generated by recent reactivation that caused the breach and subsequent leakage of the entire original hydrocarbon column.
Pay-Per-View Purchase Options
The article is available through a document delivery service. Explain these Purchase Options.
Watermarked PDF Document: $14 | |
Open PDF Document: $24 |